NDE / NDT

Audit Assistance services in Vancouver

Qualitest Canada assists the clients for their Internal or external audit process. Our highly experiences and knowledgeable professionals take care of your QMS system audit process and save the time and cost to your organization. We assist many different audits for our clients and some of them are listed below.

• QMS Gap analysis
• Internal Audit
• Document Preparation for External Audit
• Pre-Assessment audit for ISO certification
• Third party Audit as per the client requirement
• Vendor / Supplier audit as per the QMS

The baseline audit includes a gap analysis to identify any missing or weak areas of your quality system. This information is used to prepare a project plan for implementing the necessary documents and practices. We can conduct internal audits to fulfill this management system requirement for your organization.

Our pre-assessment audit provides a readiness check before the Registrar (Certification Body) arrives for the certification audit. Based on our understanding of your practices, and using our auditing experience, we can consult with you to achieve an improved and conforming system.

Based on our understanding of your practices, and using our auditing experience, we can consult with you to achieve an improved and conforming system. In addition to the ISO audit assistance, Qualitest Canada provides various project base audit services including, reviewing turnover binders, reviewing NDE reports and RT films, reviewing mud book, dossiers etc.. Qualitest Canada believes that companies must comply with demanding quality standards and regulations, such as ISO 9001, ISO 13485, MDSAP, and FDA’s QSR. Noncompliance with these requirements can impact the effectiveness of processes, affect the quality of products, and lead to the loss of certification or even a product recall.

Routine audits are required to ensure ongoing compliance to the requirements. Too often, however, routine audits only address compliance and fail to examine the company’s processes and their interactions. When non conformances are identified, the audits focus narrowly on a specific correction without considering the systemic impact of the issue or the correction. Over time, organizations can find themselves with compliant yet ineffective quality systems.

Please contact Qualitest Canada for all of your audit assistance requirements.

Please feel free to contact us for a Quote!

B.C: (778) 381-7376

Alberta: (780) 851-2020

Non-Destructive Testing Services in Vancouver Island

Qualitest is a world leader in developing and performing of Non-Destructive Testing Services in Vancouver Island. We are one of the best NDT/NDE Service Provider in Western Canada including Vancouver, Surrey, Langley, Richmond, Delta, Burnaby, Victoria, Kitimat, Dawson Creek, Kelowna, Kamloops, Edmonton, Calgary, Red Deer, Peace River, Grande Prairie, Fort McMurray, Regina, Saskatoon etc….

Our highly skilled and knowledgeable engineers and certified technicians using wide range of equipment are capable to solve different NDT problems. We providw the best Non-Destructive Testing Services in Vancouver Island. NDE/NDT can be applied for both metallic and non-metallic (e.g. polymers and composites) materials. We perform the NDE/NDT during production, post-production or in service in accordance with the project requirements. Qualitest perform the following non-destructive tests (NDT).

• Visual Inspection or Visual Testing (VT)
• Ultrasonic Inspection (UT) for Obtaining the Materials’ Thickness and the Corrosion Mapping- zero Degree Scan
• Magnetic Particle Testing (MT or MPI)
• Conventional and Computed-Gamma Radiography
• Liquid Dye Penetrate Examination (PT)
• In-situ metallography
• X-ray Fluorescence (XRF) Analysis
• Coating Condition Assessment and Coating Failure Analysis (NACE certified procedures)

Advanced NDE Services

Our services operates a full range of state-of-the-art computerized inspection tools utilizing ultrasound technology and delivering unparalleled accuracy and resolution. Our client or third party inspector will have the access to review all the stored data files.

We can provide test solutions to whatever thickness or diameter you would require:

Our Capabilities:

• Automated Ultrasonic Testing (AUT)
• Phased Array Ultrasonic Testing (PAUT)
• Time of Flight Diffraction (ToFD)
• Magnetic Flux Leakage on Tank Floors (MFL)
• Robotic Inspection – Pipelines
• Tube Inspection – ECT/IRIS/MFL/RFT
• Video scope (Manual / Borescope)

Contact us admin@qualitests.com today to get a quote.

Alberta: 702 – 23rd Ave Nisku, AB, T9E 7Y6, Canada, (780) 851-2020

BC: 112, 13085 115Ave, Surrey, BC V3R 0C3, Canada, (778) 381-7376

Structural Steel Inspection in Vancouver Island

Qualitest Canada provides Structural Steel Inspection in Vancouver Island through it’s highly qualified CWB Level 2 / Level 3 inspectors. Qualitest covers most part of the Western Canada including Vancouver, Surrey, Langley, Richmond, Delta, Burnaby, Victoria, Kitimat, Dawson Creek, Kelowna, Kamloops, Edmonton, Calgary, Red Deer, Peace River, Grande Prairie, Fort McMurray, Regina, Saskatoon etc…

Qualitest Canada’s inspectors have completed many structural steel inspection projects in the past including industrial, institutional and commercial sectors. We take care of your structural steel inspection at any stage you need our service. Our inspectors will visit to your project site and perform the Structural Steel inspection as per the project requirements.

We are capable of providing full range steel inspection in Vancouver Island BC area including visual weld inspection, magnetic particle testing, ultrasonic weld testing, lamination scans, hardness testing and bolt torque testing at the fabrication shop or in the field at the job site. In the past, we have performed full Quality Control inspection programs on offshore drilling platforms and onshore large structural steel projects such the installation of huge structural steel components at various commercial and industrial projects in lower mainland, BC. As we have many years in the structural steel inspection and testing business, we guarantee you with the experience and knowledge you are looking for. We offer a “One-Stop” testing and Inspection service that is second to none.

• Reviewing the blue prints and IFC drawings
• Bolt Tension Verification
• Column verification for verticality (plumbness)
• Verification of Column to beam connections
• Joists and bridges verification
• Metal deck installation inspection
• Rebar inspection
• Field Erection Welding Inspection and Testing
• Interpreting Applicable Codes and Standards
• Non-Destructive Testing
• Verification of Welders and Welding operators
• Verification of Welding Procedures and WPDS
• Fabrication Shop Welding Inspection and Testing

Contact us admin@qualitests.com today to get a quote.

Alberta: 702 – 23rd Ave Nisku, AB, T9E 7Y6, Canada, (780) 851-2020

BC: 112, 13085 115Ave, Surrey, BC V3R 0C3, Canada, (778) 381-7376

MFL Tank Inspection Services in Kitimat

Qualitest Canada provides MFL Tank Inspection services in Kitimat and  all over Canada including Vancouver, Surrey, Langley, Richmond, Delta, Burnaby, Victoria, Kitimat, Dawson Creek, Kelowna, Kamloops, Edmonton, Calgary, Red Deer, Peace River, Grande Prairie, Fort McMurray, Regina, Saskatoon, Montreal, Toronto, etc…

Qualitest Canada provides the top notch technical and testing solution to the Tank Floor Inspection projects. Our highly experienced technicians will perform the floor scanning and issue a detailed scan report which will be easy to understand by any individuals knows about the tanks.

Tank floor MFL scanning is a non-destructive testing method that generates a more thorough and complete inspection of the storage tank floors and walls. A strong magnetic field is used to detect pitting and corrosion in carbon plates on both top and bottom surfaces. This magnetic field is created by strong magnets in close proximity to the carbon steel floors. The magnetic field leaks from the steel where there is pitting or corrosion and a sensor alerts the technician to pay more attention to those locations.

The scanner is dragged over the entire surface of the floor, and areas of concern are verified with ultra sound to obtain wall loss readings. Technicians interpret the scanner display to identify damaged areas and in some cases, estimate the amount of metal loss. Thickness losses detected by ultrasound are reported and mapped in a CAD rendering of the floor.

Advantages

• Thorough inspection of floors in a short period of time.
• Reliable and economical results.
• Access to only one side of tank floor is needed.
• Can scan through most coatings.
• Cost effective comparatively to any other NDT methods.
• Fast method for inspecting large areas.
• Minimal set-up time.

Limitations

• UT (Ultrasonic Testing) is required to verify wall loss of defects.
• Does not decipher which side the wall loss is on.
• Inspection access is limited to areas without components which are close or attached to the floor.
• Tank Floor condition is vital to the integrity of inspection. Scales build up and debris will prevent accurate readings.
• Tank floors must be freshly cleaned and free of all debris.
• Not a quantitative technique for identifying remaining wall thickness.

MFL Tank Inspection Services in Victoria BC

Qualitest Canada provides MFL Tank Inspection Services in Victoria BC and other part of Canada including Vancouver, Surrey, Langley, Richmond, Delta, Burnaby, Kitimat, Dawson Creek, Kelowna, Kamloops, Edmonton, Calgary, Red Deer, Peace River, Grande Prairie, Fort McMurray, Regina, Saskatoon, Montreal, Toronto, etc…

Qualitest Canada provides the top notch technical and testing solution to the Tank Floor Inspection projects. Our highly experienced technicians will perform the floor scanning and issue a detailed scan report which will be easy to understand by any individuals knows about the tanks.

Tank floor MFL scanning is a non-destructive testing method that generates a more thorough and complete inspection of the storage tank floors and walls. A strong magnetic field is used to detect pitting and corrosion in carbon plates on both top and bottom surfaces. This magnetic field is created by strong magnets in close proximity to the carbon steel floors. The magnetic field leaks from the steel where there is pitting or corrosion and a sensor alerts the technician to pay more attention to those locations.

The scanner is dragged over the entire surface of the floor, and areas of concern are verified with ultra sound to obtain wall loss readings. Technicians interpret the scanner display to identify damaged areas and in some cases, estimate the amount of metal loss. Thickness losses detected by ultrasound are reported and mapped in a CAD rendering of the floor.

Advantages

• Thorough inspection of floors in a short period of time.
• Reliable and economical results.
• Access to only one side of tank floor is needed.
• Can scan through most coatings.
• Cost effective comparatively to any other NDT methods.
• Fast method for inspecting large areas.
• Minimal set-up time.

Limitations

• UT (Ultrasonic Testing) is required to verify wall loss of defects.
• Does not decipher which side the wall loss is on.
• Inspection access is limited to areas without components which are close or attached to the floor.
• Tank Floor condition is vital to the integrity of inspection. Scales build up and debris will prevent accurate readings.
• Tank floors must be freshly cleaned and free of all debris.
• Not a quantitative technique for identifying remaining wall thickness.

Non-Destructive Testing Services in Vancouver Island

Qualitest is a world leader in developing and performing of Non-Destructive Testing services. We are one of the best NDT/NDE Service Provider in Western Canada including Vancouver, Surrey, Langley, Richmond, Delta, Burnaby, Victoria, Kitimat, Dawson Creek, Kelowna, Kamloops, Edmonton, Calgary, Red Deer, Peace River, Grande Prairie, Fort McMurray, Regina, Saskatoon etc….

Our highly skilled and knowledgeable engineers and certified technicians using wide range of equipment are capable to solve different NDT problems. NDE/NDT can be applied for both metallic and non-metallic (e.g. polymers and composites) materials. We perform the NDE/NDT during production, post-production or in service in accordance with the project requirements. Qualitest perform the following non-destructive tests (NDT).

• Visual Inspection or Visual Testing (VT)
• Ultrasonic Inspection (UT) for Obtaining the Materials’ Thickness and the Corrosion Mapping- zero Degree Scan
• Magnetic Particle Testing (MT or MPI)
• Conventional and Computed-Gamma Radiography
• Liquid Dye Penetrate Examination (PT)
• In-situ metallography
• X-ray Fluorescence (XRF) Analysis
• Coating Condition Assessment and Coating Failure Analysis (NACE certified procedures)

Advanced NDE Services

Our services operates a full range of state-of-the-art computerized inspection tools utilizing ultrasound technology and delivering unparalleled accuracy and resolution. Our client or third party inspector will have the access to review all the stored data files.

We can provide test solutions to whatever thickness or diameter you would require:

Our Capabilities:

• Automated Ultrasonic Testing (AUT)
• Phased Array Ultrasonic Testing (PAUT)
• Time of Flight Diffraction (ToFD)
• Magnetic Flux Leakage on Tank Floors (MFL)
• Robotic Inspection – Pipelines
• Tube Inspection – ECT/IRIS/MFL/RFT
• Video scope (Manual / Borescope)

Welding Procedure Development Services in Victoria BC

Qualitest Canada provides welding procedure development services in Victoria BC in accordance with and welder testing through it’s highly experience engineers and professionals. Qualitest Canada serves all over Western Canada including Vancouver, Surrey, Langley, Richmond, Delta, Burnaby, Victoria, Kitimat, Dawson Creek, Kelowna, Kamloops, Edmonton, Calgary, Red Deer, Peace River, Grande Prairie, Fort McMurray, Regina, Saskatoon etc…

Qualitest Canada is a world leader in designing, testing and documentation Welding Procedure Specification (WPS) for different applications. Our highly experienced welding engineers and technicians will design welding procedure specification (WPS) based on your requirements and applicable codes and standards such as ASME, CWB, API, CSA, AWS and etc.

The welding Engineers in Qualitest Canada are specialists in welding procedure (WPS) design, testing, and documentation for new applications and repairs. Depending on your needs, we will design your welding procedure specification to various codes & standards including but not limited to ASME, CWB, API, CSA, AWS and various Project Specifications.

We are proud of our long history in successful designing and documentation of welding procedures for a broad range of applications. Qualitest Canada’s experienced engineers solve challenging problems regarding welding procedures and PQR preparation. Qulaitest provide additional services as following:

• Evaluate the existing welding procedures
• Perform welding quality control inspections and prepare documentation
• Supervise and inspect critical weld procedures in the field
• Prepare quotes for the welding part of a project

Contact us admin@qualitests.com today to get a quote.

Alberta: 702 – 23rd Ave Nisku, AB, T9E 7Y6, Canada, (780) 851-2020

BC: 112, 13085 115Ave, Surrey, BC V3R 0C3, Canada, (778) 381-7376

Structural Steel Inspection in Kamloops

Qualitest Canada provides Structural Steel Inspection in Kamloops through it’s highly qualified CWB Level 2 / Level 3 inspectors. Qualitest covers Structural Steel Inspection throughout the Western Canada including Vancouver, Surrey, Langley, Richmond, Delta, Burnaby, Victoria, Kitimat, Dawson Creek, Kelowna, Kamloops, Edmonton, Calgary, Red Deer, Peace River, Grande Prairie, Fort McMurray, Regina, Saskatoon etc…

Qualitest Canada’s inspectors have completed many structural steel inspection projects in the past including industrial, institutional and commercial sectors. We take care of your structural steel inspection at any stage you need our service. Our inspectors will visit to your project site and perform the steel structural inspection as per the project requirements.

• Reviewing the blue prints and IFC drawings
• Bolt Tension Verification
• Column verification for verticality (plumbness)
• Verification of Column to beam connections
• Joists and bridges verification
• Metal deck installation inspection
• Rebar inspection
• Field Erection Welding Inspection and Testing
• Interpreting Applicable Codes and Standards
• Non-Destructive Testing
• Verification of Welders and Welding operators
• Verification of Welding Procedures and WPDS
• Fabrication Shop Welding Inspection and Testing

Contact us admin@qualitests.com today to get a quote.

Alberta: 702 – 23rd Ave Nisku, AB, T9E 7Y6, Canada, (780) 851-2020

BC: 112, 13085 115Ave, Surrey, BC V3R 0C3, Canada, (778) 381-7376